WEKO3
アイテム
Knowledge-Based Die Design Method for Cold and Warm Forging Dies Shared in a Series of Forming Stages in Sequential Forging Press
http://hdl.handle.net/10228/0002001521
http://hdl.handle.net/10228/000200152128776a7a-165d-4e2a-acaa-dad69dcc232e
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
10430248.pdf (7.2 MB)
|
|
| Item type | 共通アイテムタイプ(1) | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 公開日 | 2025-04-01 | |||||||||||||
| タイトル | ||||||||||||||
| タイトル | Knowledge-Based Die Design Method for Cold and Warm Forging Dies Shared in a Series of Forming Stages in Sequential Forging Press | |||||||||||||
| 言語 | en | |||||||||||||
| その他のタイトル | ||||||||||||||
| その他のタイトル | Knowledge-based Die Design Method for Cold and Warm Forging Dies Shared in a Series of Forming Stages in Sequential Forging Press | |||||||||||||
| 言語 | en | |||||||||||||
| 著者 |
梅田, 政信
× 梅田, 政信× Shibai, Yusuke
× Mure, Yuji
× 片峯, 恵一
WEKO
926
|
|||||||||||||
| 著作権関連情報 | ||||||||||||||
| 言語 | en | |||||||||||||
| 権利情報 | Copyright (c) 2024 The Author(s), under exclusive license to Springer Nature Switzerland AG. This is a post-peer-review, pre-copyedit version of an article published in Lecture Notes in Mechanical Engineering. The final authenticated version is available online at: https://doi.org/10.1007/978-3-031-41341-4_40. | |||||||||||||
| 抄録 | ||||||||||||||
| 内容記述タイプ | Abstract | |||||||||||||
| 内容記述 | This paper proposes a general forging die design with sequential forging press extension (GeneDieSFX) method, which is based on an extension of the general forging die design (GeneDie) method, for totally non-axisymmetric cold- and warm-forged products that can be deformed using the sequential forging press (SFP) method. The SFP method uses two punches located on the left and right sides of the upper and lower dies and shares the same dies while exchanging these punches in all forming stages. The basic die structure, which represents the relative positional interrelationships among the various components of the forging dies, is extended to support a new die structure for the SFP method. The forming surface configuration, which represents the correspondence between the functions allocated to the surfaces of the forging dies and the surfaces of the forged product, is also extended to distinguish the forming surfaces of the two punches that press the work material from the left and right sides. In addition, a die unification procedure is introduced to share the dies in all forming stages. An experimental knowledge base for die design support was developed and applied to process plans designed by an experienced engineer for forming of an electrical connector. The experimental results show that the proposed method can generate forging dies that are functionally comparable with dies designed by the experienced engineer. | |||||||||||||
| 言語 | en | |||||||||||||
| 備考 | ||||||||||||||
| 内容記述タイプ | Other | |||||||||||||
| 内容記述 | 14th International Conference on the Technology of Plasticity, ICTP 2023, September 24-29, 2023, French Riviera, France | |||||||||||||
| 言語 | en | |||||||||||||
| 書誌情報 |
en : Lecture Notes in Mechanical Engineering p. 389-401, 発行日 2023-08-29 |
|||||||||||||
| 出版社 | ||||||||||||||
| 出版者 | Springer | |||||||||||||
| キーワード | ||||||||||||||
| 言語 | en | |||||||||||||
| 主題Scheme | Other | |||||||||||||
| 主題 | Basic die structure | |||||||||||||
| キーワード | ||||||||||||||
| 言語 | en | |||||||||||||
| 主題Scheme | Other | |||||||||||||
| 主題 | Forming surface configuration | |||||||||||||
| キーワード | ||||||||||||||
| 言語 | en | |||||||||||||
| 主題Scheme | Other | |||||||||||||
| 主題 | Non-axisymmetric forged product | |||||||||||||
| キーワード | ||||||||||||||
| 言語 | en | |||||||||||||
| 主題Scheme | Other | |||||||||||||
| 主題 | Die unification | |||||||||||||
| 言語 | ||||||||||||||
| 言語 | eng | |||||||||||||
| 資源タイプ | ||||||||||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||||||||||
| 資源タイプ | journal article | |||||||||||||
| 出版タイプ | ||||||||||||||
| 出版タイプ | AM | |||||||||||||
| 出版タイプResource | http://purl.org/coar/version/c_ab4af688f83e57aa | |||||||||||||
| DOI | ||||||||||||||
| 識別子タイプ | DOI | |||||||||||||
| 関連識別子 | https://doi.org/10.1007/978-3-031-41341-4_40 | |||||||||||||
| ISBN | ||||||||||||||
| 識別子タイプ | ISBN | |||||||||||||
| 関連識別子 | 978-3-031-41340-7 | |||||||||||||
| ISSN | ||||||||||||||
| 収録物識別子タイプ | PISSN | |||||||||||||
| 収録物識別子 | 2195-4356 | |||||||||||||
| ISSN | ||||||||||||||
| 収録物識別子タイプ | EISSN | |||||||||||||
| 収録物識別子 | 2195-4364 | |||||||||||||
| 会議記述 | ||||||||||||||
| 会議名 | 14th International Conference on the Technology of Plasticity, ICTP 2023 | |||||||||||||
| 言語 | en | |||||||||||||
| 回次 | 14 | |||||||||||||
| 開始年 | 2023 | |||||||||||||
| 開始月 | 09 | |||||||||||||
| 開始日 | 24 | |||||||||||||
| 終了年 | 2023 | |||||||||||||
| 終了月 | 09 | |||||||||||||
| 終了日 | 29 | |||||||||||||
| 開催国 | FRA | |||||||||||||
| 査読の有無 | ||||||||||||||
| 値 | yes | |||||||||||||
| 研究者情報 | ||||||||||||||
| URL | https://hyokadb02.jimu.kyutech.ac.jp/html/304_ja.html | |||||||||||||
| 研究者情報 | ||||||||||||||
| URL | https://hyokadb02.jimu.kyutech.ac.jp/html/307_ja.html | |||||||||||||
| 論文ID（連携） | ||||||||||||||
| 値 | 10430248 | |||||||||||||
| 連携ID | ||||||||||||||
| 値 | 12175 | |||||||||||||
