WEKO3
アイテム
How to obtain the adhesive strength for double lap joint by using single lap joint
http://hdl.handle.net/10228/00006714
http://hdl.handle.net/10228/000067144c466943-594a-447d-a3d0-3e6435960569
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
J.Phys.Conf.Ser._843_012006.pdf (971.9 kB)
|
|
| アイテムタイプ | 学術雑誌論文 = Journal Article(1) | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 公開日 | 2018-04-24 | |||||||||||||
| 資源タイプ | ||||||||||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||||||||||
| 資源タイプ | journal article | |||||||||||||
| タイトル | ||||||||||||||
| タイトル | How to obtain the adhesive strength for double lap joint by using single lap joint | |||||||||||||
| 言語 | en | |||||||||||||
| 言語 | ||||||||||||||
| 言語 | eng | |||||||||||||
| 著者 |
野田, 尚昭
× 野田, 尚昭
WEKO
3665
× Li, R× 佐野, 義一× 高瀬, 康× Takaki, R× Miyazaki, T |
|||||||||||||
| 抄録 | ||||||||||||||
| 内容記述タイプ | Abstract | |||||||||||||
| 内容記述 | The testing method of adhesive strength of lap joint is prescribed in Japanese Industrial Standard (JIS K6850). However, it has been reported that the strength of double lap joint (DLJ) is about two times larger than the one of single lap joint (SLJ). Therefore, suitable testing method has been required from industries. In this study, the equivalent conditions of strength for SLJ and DLJ are investigated in terms of the intensity of singular stress field (ISSF) appearing at the interface end. First, in order to minimize the bend effect for SLJ, the effect of the specimen geometry on ISSF and deformation angle at the interface corner is considered under the same adhesive geometry and load P. It is found that the minimum ISSF of SLJ can be obtained when the adherend thickness t1 is large enough, and the deformation angle at interface corner is also smallest when adherend thickness t1 is large enough. Therefore, it is necessary to use the specimen with thicker adherend thickness. Then, the equivalent conditions of strength for SLJ and DLJ is investigated by changing adherend thickness. The results show that the strength of the DLJ in JIS (t1=1.5mm) can be obtained by using the SLJ with adherend thickness t1=7mm. When the adherend thickness t1≥25mm, the strength of SLJ is nearly equal to that of DLJ. | |||||||||||||
| 言語 | en | |||||||||||||
| 備考 | ||||||||||||||
| 内容記述タイプ | Other | |||||||||||||
| 内容記述 | 6th International Conference on Fracture Fatigue and Wear, 26–27 July 2017, Porto, Portugal | |||||||||||||
| 書誌情報 |
en : Journal of Physics: Conference Series 巻 843, 号 1, p. 012006-1-012006-6, 発行日 2017-05-31 |
|||||||||||||
| 出版社 | ||||||||||||||
| 出版者 | IOP Publishing | |||||||||||||
| 言語 | en | |||||||||||||
| DOI | ||||||||||||||
| 関連タイプ | isIdenticalTo | |||||||||||||
| 識別子タイプ | DOI | |||||||||||||
| 関連識別子 | https://doi.org/10.1088/1742-6596/843/1/012006 | |||||||||||||
| ISSN | ||||||||||||||
| 収録物識別子タイプ | PISSN | |||||||||||||
| 収録物識別子 | 1742-6588 | |||||||||||||
| ISSN | ||||||||||||||
| 収録物識別子タイプ | EISSN | |||||||||||||
| 収録物識別子 | 1742-6596 | |||||||||||||
| 著作権関連情報 | ||||||||||||||
| 権利情報Resource | http://creativecommons.org/licenses/by/3.0 | |||||||||||||
| 権利情報 | Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence (http://creativecommons.org/licenses/by/3.0). Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI. Published under licence by IOP Publishing Ltd | |||||||||||||
| 出版タイプ | ||||||||||||||
| 出版タイプ | VoR | |||||||||||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||||||||||
| 査読の有無 | ||||||||||||||
| 値 | yes | |||||||||||||
| 研究者情報 | ||||||||||||||
| URL | https://hyokadb02.jimu.kyutech.ac.jp/html/10_ja.html | |||||||||||||
| 論文ID（連携） | ||||||||||||||
| 値 | 10316067 | |||||||||||||
| 連携ID | ||||||||||||||
| 値 | 6908 | |||||||||||||
